Product Overview

Introduction of Pneumatic Anchor Drilling Rig

Pneumatic anchor drilling rig is a kind of anchor drilling rig that uses air pressure to operate, and it is an important equipment of the roadway boring equipment for coal mines, which has outstanding superiority in improving the support effect, reducing cost, speeding up the speed of tunneling, reducing the amount of auxiliary transportation, reducing labor intensity, and increasing the utilization rate of the roadway section.

MQT130 pneumatic anchor drilling rig introduction MQT-130/2.0 pneumatic anchor drilling rig is mainly used for drilling anchor rods and anchor cable support holes in coal mine rock hardness ≤ f10 in coal mine and rocky roadway, and it can stir and install resin anchor rods and anchor cables, for the anchor rods with damping nut, MQT-130/2.0 pneumatic anchor drilling rig can directly tighten the nut during stirring, so as to realize the anchor stirring and installation in one time, and to meet the requirements of the preliminary anchor pre-tensioning force. MQT130/2.0 type pneumatic anchor drilling rig can realize anchor mixing and installation in one time and meet the requirement of initial anchor preload.

MQT130 Pneumatic Anchor Drilling Rig Features

1、 Maximum use of engineering plastic materials, light weight, easy to operate. 2、 MQT-130/2.0 pneumatic anchor drilling rig adopts large-size motor as power, with larger power-to-weight ratio and longer service life. 3, The parameter matching is more reasonable, the drilling rig reaches the maximum output power when the drilling speed is near the best. 4、The propulsion part adopts new type fiberglass cylinder, which is safe and explosion-proof, lightweight and flexible. 5、The new water valve with patented technology can adapt to the ultra-high surface hydrostatic water in coal mine.

Introduction of MQT120 Pneumatic Anchor Drilling Rig

MQT120 Pneumatic Anchor Drilling Rig maximizes the use of engineering plastic materials, light weight, easy to operate.MQT-120 Pneumatic Anchor Drilling Rig adopts large-size motors for power, with greater power-to-weight ratio and longer service life. The parameter matching is more reasonable, the drilling rig reaches the maximum output power when the drilling speed is near the optimal drilling speed.The propulsion part of MQT-120 pneumatic anchor drilling rig adopts a new type of glass fiber reinforced plastic cylinder, which is safe and explosion-proof, lightweight and flexible. The new water valve with patented technology can adapt to the ultra-high surface hydrostatic water in coal mine.

MQT130

Working air pressure: Mpa 0.4-0.63 Rated air pressure: Mpa 0.5 Rated speed: r-min 206 Rated torque: N.m 130 Stall torque: N.m 220 No-load speed: r-min ≥ 560 Air consumption: m3-min 4.5 Maximum thrust: KN 8 Flushing water pressure: Mpa 0.6-1.2

MQT120

Working pressure: MPa 0.40 0.50 0.63 Rated torque: N-m 100 120 130 Rated speed: r/min 190 220 240 Propulsive force Grade 1 kN 6.6 8.2 9.8 Secondary kN 5.2 6.5 8.1 Grade 3 kN 4.1 5.1 6.4 Maximum output power kW: 1.9 2.7 3.2 No-load speed r/min: ≥540 ≥580 ≥620 1/2 no-load speed r/min: 270 290 310 Torque at 1/2 no-load speed N-m: 75 85 95 Starting torque N-m: 175 225 260 Stall torque N-m: 185 235 270 Maximum load torque N-m: 165 215 250 Air consumption m³/min: 3.2 4.2 5.3 Noise Sound pressure level dB(A): ≤93 ≤95 ≤98 Sound power level dB(A): ≤110 ≤112 ≤115 Model: S M H Maximum height mm: 2457±50 3057±50 3657±50 Minimum height mm: 1150±50 1300±50 1450±50 Push stroke mm: 1307 1757 2207 No-load propulsion speed m/s: 2 Propulsion. Stroke primary mm: 740±50 Secondary mm: 720±50 Tertiary mm: 730±50 Machine weight kg: 48 50 52 Drill end connection size mm: S=19,22 Drilling diameter mm: φ32 Flushing water pressure MPa: 0.6-1.2

MQS-50 handheld anchor drilling rig introduction MQS-50/1.8 type pneumatic hand-held gang anchor drilling rig is mainly used for drilling coal gang anchor support holes in coal mine rock hardness ≤ f6 coal mine, semi-coal mine, and mixing and installing resin anchor rods; it can also be used for drilling small-size holes for water detection, gas detection, or artillery holes. The control handle is made of alloy steel, which is of high strength and not easily damaged, prolonging the service life. The output brazing sleeve can be used both for drilling with B19 drill rods and twist drill rods. 
 

MQS-50 handheld anchor drilling rig product features Small size, light weight, simple operation and easy maintenance. Metal motor gear, longer service life. Stable operation, high reliability. Safe and explosion-proof, reasonable structure, strong adaptability. MQS-50 hand-held anchor drilling rig technical parameters Working air pressure Mpa0.4-0.63 Rated air pressure Mpa0.5 Rated speed r/min320 Rated torque N.m50 Stall torque N.m57 No-load speed r/min≥ 1000 Air consumption m3/min4 Flushing water pressure (wet drilling) Mpa0.6-1.2 Noise dB(A) ≤ 95 Weight of the whole machine Kg13.5

Introduction of MQS-35 Handheld Anchor Drilling Rig MQS-35 hand-held anchor drilling rig is a portable drilling rig, which has the features of large torque, light weight, small volume, reversible, simple structure and easy maintenance, etc. Compared with similar drilling rigs, this drilling rig has larger torque, faster rotation speed and greater function, so this drilling rig has high working efficiency, low labor intensity of workers' operation, and less cost of footage. MQS-35 pneumatic hand-held gang anchor drilling rig is suitable for the support operation of coal gang anchor in coal tunnel and semi-coal tunnel with rock hardness ≤ f6, which can not only drill anchor holes, but also mix and install resin medicine anchor. 
 

MQS35 handheld anchor drilling rig product features Working pressure .4～0.63MPa 0 Rated pressure 0.5MPa Rated torque ≥35N.m Rated speed 600r/min No-load speed ≥1300r/min Maximum output power ≥1.6kW Noise ≤90dB(A) Maximum load torque ≥70N.m Air consumption ≤2.4m3/min Weight 11.5 kg Flushing water pressure (wet drilling) 0.6～1.2MPa Maximum drilling diameter Φ≤42mm